[Rwp] sidechaining.

[Justin Macleod]

That means that channels 1 and 2 of your send are sending to channels 3 and
4 of your receive, where your compressor/gate/vocoder/whatever will be
listening for the audio to turn up. 

Hope this helps, 

Justin 

-----Original Message-----
From: RWP [mailto:rwp-bounces at bluegrasspals.com] On Behalf Of Roger
Alexanderson via RWP
Sent: 03 September 2015 19:20
To: Reapers Without Peepers <rwp at bluegrasspals.com>
Cc: Roger Alexanderson <roger77swe at yahoo.com>
Subject: Re: [Rwp] sidechaining.

just a bit confused, 1+2=3+4?

Den 2015-09-03 kl. 17:22, skrev Alex H. via RWP:
> You have it correct.
>
> alex
>
> On 9/1/15, theoreomonster--- via RWP <rwp at bluegrasspals.com> wrote:
>> just to clarify if i wanted the bass to duct overtime the kick hits, 
>> i would make the bass track a 4 channel track and put the compressor 
>> on that one and set the input to 3/4, then set the kick drum track to 
>> 1/2>=3/4? Or is it the other way around ?
>>> On Sep 1, 2015, at 10:15 PM, Alex H. via RWP <rwp at bluegrasspals.com>
>>> wrote:
>>>
>>> hi,
>>>
>>> Make your receiving track (the one with the effect u wanna use as a 
>>> side chaining thing) a 4 channel track.
>>> On the effects on that track, Set the input on the plugin to 
>>> channels 3/4. It's sometimes called auxiliary.
>>>
>>> Go to the other track, the one with the audio you wish to manipulate 
>>> and bring up the track routing dialog. It's I with reaaccess; not 
>>> sure with OSARA.
>>> Find the buttons that say audio 1/2 and >=1/2. Press on the >= one 
>>> and select 3/4. Done.
>>>
>>> Hope this helps, jotting down from memory as I don't have any access 
>>> to Reaper to double check. Someone else will chime in who knows 
>>> their stuff I'm sure :)
>>>
>>> alex
>>>
>>> On 8/31/15, Roger Alexanderson via RWP <rwp at bluegrasspals.com> wrote:
>>>> hi.
>>>> I'm trying to get sidechain compression to work but it's a bit of a 
>>>> hazard.
>>>> i followed instruction on the cockos forums.
>>>> http://forum.cockos.com/showthread.php?t=17729
>>>> the first problem i found was it's a bit tricky to get the in and 
>>>> outs right in the i/o routing dialogue.
>>>> secondly the plugin pin connector doesn't seem to be accessible at 
>>>> all, at least not in reacomp.
>>>> any ideas.
>>>> thanks
>>>> _______________________________________________
>>>> RWP mailing list
>>>> RWP at bluegrasspals.com
>>>> http://bluegrasspals.com/mailman/listinfo/rwp
>>>>
>>> _______________________________________________
>>> RWP mailing list
>>> RWP at bluegrasspals.com
>>> http://bluegrasspals.com/mailman/listinfo/rwp
>>
>> _______________________________________________
>> RWP mailing list
>> RWP at bluegrasspals.com
>> http://bluegrasspals.com/mailman/listinfo/rwp
>>
> _______________________________________________
> RWP mailing list
> RWP at bluegrasspals.com
> http://bluegrasspals.com/mailman/listinfo/rwp
>

_______________________________________________
RWP mailing list
RWP at bluegrasspals.com
http://bluegrasspals.com/mailman/listinfo/rwp