[Rwp] Getting Reaper 5 to work with the bcf2000

[Jes]

Original message:
> How'd it work? I have the other two nano things but not the controller.
> At some point I should try hooking my Axiom up and see if I can get it
> to control things any better than it did in Sonar, which wasn't very
> well. But the Nano controller would be a nice little thing to have lying
> around if it worked decently, especially if I needed to be portable at
> some point.

> On 12/30/2015 18:01, Patrick Perdue wrote:
>> Yep, Klinke Mackie Universal Control... Doesn't look like it's been
>> updated in a while. I used this instead of the standard Reaper
>> included Mackie Universal Control protocol with my Korg NanoKontrol2,
>> because the nobs behaved better, and I think more buttons were
>> supported by default, or something. It's been a couple of years since
>> I've really tried to do anything serious with it.
>> I bought that control surface for one project, used it for that, then
>> pretty much haven't touched it since.

>> On 12/30/2015 2:21 PM, Bryan Smart wrote:
>>> The Behringer site will say how to get it to run in Mackie Control
>>> mode, but, for the BCF2000, I remember that you probably shouldn't
>>> use Reaper's standard Mackie Control support. There is some add-on
>>> called Klinky, or similar. Check Reaper forums.



>>> Bryan

>>>> On Dec 30, 2015, at 10:30 AM, Chris Smart <csmart8 at cogeco.ca> wrote:

>>>> also check the Reaper forums, not just the blind-specific listserves.
>>>> http://forum.cockos.com/forumdisplay.php?f=20



>>>> At 01:51 AM 12/30/2015, you wrote:
>>>>> Behringer’s site should have support documents  covering this. > On
>>>>> Dec 29, 2015, at 8:37 AM, Jes <jessmith at samobile.net> wrote: > > Hi
>>>>> list, > Just got a BCF2000 and am wondering how to set it up as a
>>>>> control surface in Reaper. What mode should I put the BCF2000 in
>>>>> when I start it up, and what control surface settings do I need in
>>>>> Reaper's prefs? > Thanks. > > Jes >
>>>>> _______________________________________________ >  RWP mailing list
>>>>>> RWP at bluegrasspals.com >
>>>>> http://bluegrasspals.com/mailman/listinfo/rwp
>>>>> _______________________________________________ RWP mailing list
>>>>> RWP at bluegrasspals.com http://bluegrasspals.com/mailman/listinfo/rwp

>>>> ---
>>>> <http://www.shareasale.com/r.cfm?b=635671&u=1109457&m=54749&urllink=&afftrack=>Learn
>>>> to meditate and train your brain with Muse, the first lab-grade EEG
>>>> biofeedback headband for home use!

>>>> _______________________________________________
>>>> RWP mailing list
>>>> RWP at bluegrasspals.com
>>>> http://bluegrasspals.com/mailman/listinfo/rwp

>>> _______________________________________________
>>> RWP mailing list
>>> RWP at bluegrasspals.com
>>> http://bluegrasspals.com/mailman/listinfo/rwp


>> _______________________________________________
>> RWP mailing list
>> RWP at bluegrasspals.com
>> http://bluegrasspals.com/mailman/listinfo/rwp

> _______________________________________________
> RWP mailing list
> RWP at bluegrasspals.com
> http://bluegrasspals.com/mailman/listinfo/rwp
I installed the klinke Mackie universal control. I notice whenever I 
load it in the reaper control surfaces prefs, it always says preset 1, 
even when I have the BCF2000 booted into preset 2. How do I change the 
control surface to preset 2 in the reaper prefs?
Jes